Gas Cylinder Cage — LPG and Oxygen Cylinder Storage Cages (9kg, 19kg, 47kg, 48kg)

A gas cylinder cage is a restraint system first and a storage unit second

A filled LPG or oxygen cylinder is a pressure vessel with a valve on top, and the valve is the part that fails when a cylinder goes over. A gas cylinder cage exists to make sure that cannot happen: the cylinders stand upright, they are held apart from each other, they cannot be knocked over by a forklift, and the whole group can be lifted and moved without anyone unclipping a chain.

We build gas cylinder storage cages for LPG, oxygen, acetylene, nitrogen and CO₂ service, in sizes that follow the cylinders you actually hold rather than a nominal capacity figure.

Sizing starts with the cylinder, not the cage

Australian and New Zealand buyers size a gas cage by the cylinders that go in it, and the numbers you will see in a specification are cylinder weights, not cage weights. The common LPG sizes in the region are:

Cylinder size What it usually is What it does to the cage design
9 kg Domestic and light commercial BBQ / patio cylinder Short and wide — cage needs a low deck level and closer post spacing so the cylinders cannot tip into each other
19 kg Commercial kitchen, heater and small process use The most common commercial size; usually the default when a buyer does not specify
47 kg High-volume commercial and light industrial Tall and heavy — cage needs a taller frame and forklift access that does not foul the valve
48 kg Forklift LPG, and some industrial exchange programmes Frequently handled with the cage, so lifting points and base stiffness drive the design

Tell us the cylinder size, the count, and whether the cage is filled and emptied by hand or by forklift. Those three answers fix the frame. A cage designed around 19 kg cylinders will not safely hold 47 kg ones, because the centre of gravity moves up and the post spacing was set for a shorter body.

Types of gas cylinder cage we build

Configuration Description Typical use
Static gas cylinder storage cage Fixed mesh cage with a full-height lockable door, forklift pockets in the base, stacking posts on top Yard storage outside a workshop or kitchen
Gas bottle enclosure Solid or louvred panel enclosure on three sides with a ventilated roof and a lockable front Where cylinders must be screened from view or from weather
Outdoor gas cylinder cage Hot-dip galvanised frame on a raised deck, so cylinders stand clear of standing water Coastal and exposed yards
Gas cylinder transport cage Reinforced base and side restraint for road or sea movement Moving cylinders between sites
Gas cylinder trolley Small wheeled frame for one to a few cylinders Point-of-use movement inside a workshop
Forklift gas cylinder cage Compact cage shaped to sit on the forklift or beside it, for LPG exchange Forklift fleets running on LPG

What a specification looks like

Here is a real unit from our range, the YG-S03 oxygen and gas cylinder storage cage, so you can see the level of detail we work to:

Parameter YG-S03
External length 1,428 mm
External width 1,158 mm
External height 2,350 mm
Internal length 1,218 mm
Internal width 948 mm
Internal height 1,931 mm
Internal cubic capacity 14 m³
Maximum payload 2,000 kg
Materials Mild Q235 steel, welded frame
Finish Powder coated or hot-dip galvanised
Options Lockable door, top lid, forklift guide, identification plate

Load ratings across the gas cage range sit within our standard 300 – 3,000 kg band, and frame sizes within 500 – 6,000 mm. Anything outside that is a conversation, not a refusal.

The design points that matter more than the dimensions

  • Ventilation. LPG is heavier than air. A cage with a solid floor and solid sides becomes a gas trap, so the deck and low panels are open or louvred and the cage sits clear of the ground.
  • Separation. Individual cylinder positions — dividers, cradles or post spacing — stop cylinders rubbing and knocking each other over when the cage is moved.
  • Upright restraint. A chain across the front is not restraint; a full-height frame with a positive latch is. The cylinder’s own height is what tips it.
  • Lifting that does not load the valve. Forklift pockets are formed in the base frame. Nothing lifts by the top of the cage where the cylinder valves are.
  • Lockability. A hasp and staple that takes your padlock — this is an insurance and site-audit question as often as a security one.
  • Corrosion. Gas cages usually live outdoors. In coastal Australia and New Zealand we specify hot-dip galvanised as standard rather than optional.

On compliance — read this before you order

Storage and handling of gas cylinders in Australia is governed by standards that buyers and their insurers reference, principally AS 4332 for gases in cylinders and AS 1596 for LP Gas. Those standards set out separation distances, ventilation, signage, quantities per store and segregation of incompatible gases — and the obligations fall on the site operator, not on the cage manufacturer.

To be plain about what we are and are not: we are a steel fabricator, not a certifying body. We build the cage to the dimensions, restraint arrangement and finish your specification calls for, and we will build to a drawing your engineer or safety consultant provides. We do not issue compliance certification, and we would be wary of any fabricator who offers to. If your site requires a certified installation, engage a consultant on the standards side and we will fabricate to their design.

Related products

Frequently asked questions

How many cylinders does a gas cylinder cage hold?

It depends entirely on the cylinder size, so any supplier quoting a cylinder count without asking for the size is guessing. A cage that holds twelve 19 kg cylinders will not hold twelve 47 kg ones. Give us the cylinder size and count and we will size the cage around them.

Do you make cages for 47 kg and 48 kg cylinders?

Yes. The taller the cylinder, the more the frame has to resist tipping rather than just contain, so 47 kg and 48 kg cages get a taller frame and a different post spacing than 19 kg units.

Is mesh or solid panel better for a gas cage?

Mesh for anything stored outdoors or in a plant room, because ventilation matters more than screening. Solid or louvred panels are used where cylinders have to be hidden from public view — but only with a ventilated top and an open base, never as a sealed box.

Can the cage be moved with cylinders inside?

Within a site, yes, if the cage was designed for it — that means a reinforced base and a positive front restraint rather than a chain. For road transport, specify the transport variant, because the load case is different and the base needs to take braking forces.

Do you supply to Australia and New Zealand?

Yes, both are established markets. Australian and New Zealand buyers typically specify cylinder size in kilograms and want hot-dip galvanised finish, and we build to that convention rather than to a metric-nominal catalogue.

What finish do you recommend?

Hot-dip galvanised for anything outdoors, which is most gas cages. Powder coating is fine for an indoor plant room but will not survive a coastal yard, and a rusted base is a restraint problem rather than a cosmetic one.



Post time: 2026-11-18 10:11:03
[sharethis-inline-buttons]
INQUIRY NOW

Technical guides

Reference notes for buyers specifying steel storage equipment — sizes, load ratings, coating choice and container loading.