Steel stillages, built to your load — not adapted from a pallet
A stillage is a returnable steel frame with its own deck and posts, so the load is held without stretch wrap and can be stacked several tiers high. We manufacture them in Foshan and ship to Australia, New Zealand and the wider Pacific, where the same unit is called a stillage, a stillage cage, a pallet stillage or a post pallet depending on which state the buyer works in.
Every stillage we make starts from your part drawing or your load dimensions. Load ratings run from 300 kg to 3,000 kg and overall sizes from 500 mm to 6,000 mm, which covers everything from a small automotive bracket stillage to a six-metre scaffold or glass frame.
The stillage types we manufacture
Buyers searching for stillages usually have one of six jobs in mind. The table below sets out which frame suits which job — the differences matter, because the wrong frame either will not stack or will not take the point load.
| Type | How it is built | Best for |
|---|---|---|
| Solid-deck post stillage | Steel sheet deck on a welded base frame, four corner posts, lift-out end gates | Castings, forgings, machined parts — anything that would drop through mesh |
| Mesh stillage | Welded wire mesh sides on a steel base, often with a half-drop gate | Mixed small parts where visibility and ventilation matter |
| Stackable stillage | Welded stacking legs or corner sockets that seat on the unit below | Yard and shop-floor storage two to four tiers high |
| Collapsible stillage | Hinged or lift-out sides that fold flat for the return leg | Export loops where empty containers are shipped back |
| Scaffold stillage | Long open-topped frame with end racks and lifting points | Scaffold tube, standards and ledgers — see below |
| Glass stillage | A-frame or vertical rack with lined contact points | Glass panels, windscreens, stone slabs |
Specification range
| Parameter | Range we build |
|---|---|
| Load rating | 300 – 3,000 kg per stillage |
| Overall size | 500 – 6,000 mm (length, width or height) |
| Deck | Solid steel sheet, perforated sheet, slatted, or timber on steel bearers |
| Sides and ends | Fixed, hinged, lift-out, half-drop gate, or open with removable posts |
| Finish | Hot-dip galvanised, pre-galvanised, or powder coated to your RAL colour |
| Stacking | Two, three or four high — stated per design after the load case is confirmed |
| Handling | Forklift pockets formed into the base frame; crane lifting points where specified |
| Identification | Plate holder or stencilled panel for your part number and barcode |
Because the frame is welded rather than bolted, the stacking load travels down the posts to the ground — a bolted knockdown post pallet loses that path the moment a bolt works loose.
Stillage feet and replacement parts
Stillage feet are the part that wears out first: they take the impact every time the unit is set down, and a bent foot is what stops a stack sitting level. We supply replacement feet, corner sockets, gate frames, pin latches and deck panels for stillages already in service, matched to the original design where you still have the drawing and reverse-engineered where you do not.
If you are running a fleet of stillages and replacing whole units because of damaged feet, that is usually the most expensive way to solve it. Send us photographs of the foot and the corner post and we will quote the part rather than the unit.
Scaffold stillages
Scaffold tube is awkward to store and expensive to lose. A scaffold stillage is a long, open-topped steel frame with racked ends that holds standards, ledgers and transoms in one lift, and it stacks with the tube inside so a yard can be organised vertically instead of in loose bundles.
We build these to the lengths your tube actually comes in, with end racks positioned so the tube cannot slide out under braking or during a lift. Lifting points are welded to the base frame rather than to the side rails, so the frame is not loaded in a direction it was not designed for.
Why steel instead of timber pallets
The case for a stillage is almost always made on cycle count rather than purchase price. A timber pallet is used once or twice across an export loop and then either repaired or landfilled; a steel stillage is designed to make the loop dozens of times, and it carries the load through the frame instead of through the deck.
Three things tend to decide it:
- Stacking height. Timber pallets in a rack give you the rack height. A stacking stillage gives you the same footprint at two to four tiers without racking.
- Part protection. A solid deck and enclosed ends stop small parts migrating across the container during transit — the single most common cause of damaged automotive and casting shipments.
- Return freight. Collapsible and nesting designs cut the empty return volume, which is where a stillage loop either pays or does not.
How to specify a stillage
Six questions get you a drawing rather than a guess:
- What is the part, and what does one full load weigh? We need the total, not the unit weight.
- What are the load’s outer dimensions, including any overhang?
- How many tiers do you need to stack, and will the bottom unit sit on the floor or in a rack?
- How is it loaded — overhead crane, forklift, or by hand from the side?
- Does it come back empty, and if so does it need to collapse or nest?
- Where does it live — indoor, or outdoors in salt air? Coastal yards should specify hot-dip galvanised, not powder coated.
Answer those and we return a drawing with the load case and stacking arrangement marked, for you to approve before anything is cut.
Related guides
- What is a steel stillage? Definition, uses and how buyers specify them
- How to choose stillage size, load rating and container fit
- Stillage vs wire mesh container vs storage cage
- How many stillages fit in a 40HQ container
Frequently asked questions
What is the difference between a stillage and a pallet cage?
A pallet cage is usually mesh on all four sides with a pallet base. A stillage normally has a solid deck and a heavier post frame, so it takes higher point loads and stacks without racking. In practice the terms overlap, and many buyers use them interchangeably — the drawing matters more than the name.
Can stillages be stacked without racking?
Yes — that is the main reason buyers move from pallets to stillages. Stacking legs or corner sockets carry the load from the unit above straight down to the floor. The number of tiers depends on the load and the frame section, and we state it on the drawing rather than in a brochure.
Do you supply stillages to Australia and New Zealand?
Yes, both are established markets for us, along with Canada, Brazil and Europe. We build to the load and dimension you specify rather than to a single catalogue size, and finish to suit the climate the unit will live in.
Can you replace feet or gates on stillages we already own?
Usually. Send a photograph of the worn part with a tape measure across it and the corner post it sits in. If you have the original drawing, so much the better; if not, we work from the photographs.
What finish should we choose for an outdoor yard?
Hot-dip galvanised. Powder coating looks better on a showroom floor but a chip in a coastal yard becomes a rust blister, and a rust blister under a stacked load is a structural issue rather than a cosmetic one.
Do you make stillages for glass and stone?
Yes. A-frame and vertical rack stillages with lined contact faces are built for glass panels, windscreens and stone slabs, sized to the largest panel in the batch.
Post time: 2026-11-18 10:11:48 [sharethis-inline-buttons]

