When a Steel Stillage Is the Wrong Answer

Most enquiries we receive are not really about stillages. They are about a load that has started to misbehave — a stack that leans, a cage that bowed, a bin nobody can move without two people and a pallet jack. The stillage is usually the third or fourth thing the buyer has tried, and by the time it reaches us it has been written into a specification that nobody has re-examined.

So before we quote, we ask four questions. Two of them regularly end with us recommending something we do not make. That is the point of this page.

Question 1: where does the load actually sit?

A stillage carries its load on a deck, and the deck sits on feet you can get forks under. That single sentence contains its whole advantage and its whole limit.

If the load is heavy and moves between a truck, a dock and a rack, the stillage wins — it is handled by the same forklift that handles everything else on site, and it needs no racking in order to be stored.

If the load is light and volumetric, and the site already has racking, the stillage is a cost with no return. You are paying for steel that exists only to be lifted by a machine you already have. This is the most common case where we tell a buyer not to buy what they asked for.

Question 2: does it stay on site, or does it leave?

A stillage is a transport device that happens to store. If the container never leaves the yard, you are paying transport-grade construction for a static problem — thicker sections, feet, and fork clearance that nothing on site will ever use.

Run the count: how many trips does this unit make per year? If the answer is under about ten, look hard at whether a static rack or a fixed bin would do the same job with less steel.

Question 3: does the load need to be seen, washed, or kept out?

Three answers push in three different directions.

  • Seen. Mesh. A wire mesh container lets an operator or a camera read the load without opening anything. It is why mesh dominates in logistics and rental fleets.
  • Washed. Mesh, but with attention to the welds. Washdown kills mild steel at the welds long before it kills the panel, because the weld destroys the coating directly above it. Galvanising after fabrication is the answer; painting before assembly is not.
  • Kept out, or small parts. Plate. A solid-sided bin beats mesh for fasteners, castings and anything that leaks through a 50 mm aperture. Bulky plate bins also resist side impact that folds a mesh panel flat.

If a buyer is choosing between mesh and plate, the honest answer is that they are choosing between visibility and containment, and no single container does both well.

Question 4: how many tiers — and is it the forklift or the pallet jack that matters?

Stacking changes the corner post, not the deck. A unit drawn for two tiers and used at four will not fail at the deck. It will fail where the post meets the top frame, and it will do so slowly enough that nobody notices until it does.

The second half of this question is more practical than it sounds: if a pallet jack has to enter the base, the base height decides everything else, including how much of your stack height you have given away to clearance. Where a site runs both forklifts and pallet jacks — which is most Australian warehouses — specify for the pallet jack and let the forklift have an easy life.

Where a stillage wins outright

To be fair to the product, there are cases where nothing else comes close:

  • Loads that leave the site and come back, over and over — rental fleets, site deliveries, inter-plant transfers.
  • Loads that need forking from four sides where there is no rack in the aisle.
  • Loads that must be stacked on each other, not on racking, which is most yards and most docks.
  • Irregular loads a pallet cannot hold — stone slabs, glass, long sections, gas cylinders. These need a purpose-built frame, and a frame is a stillage whether or not you call it one.

The comparison, on five lines

Most specification arguments dissolve once the options sit side by side against what the load actually needs. This is the table we use internally.

Option Forks under Stacks on itself Leaves the site Needs racking Weak at
Steel stillage Yes, usually four sides Yes Yes No Small parts, visibility
Pallet cage Yes Yes Often No Fine parts falling through the mesh
Plate bin Yes Yes Yes No Visibility, washdown drainage
Static rack No — beam level only No No Yes, by definition Mobility
Wooden crate Limited Light loads only One-way export No Reuse in wet conditions

Read the “leaves the site” column first. It is the line that decides most projects, and it is the one buyers skip.

Before you send a sketch: the five numbers that decide the drawing

Every usable specification we receive contains the same five things. Every specification that turns into three rounds of emails is missing at least one of them.

  1. Footprint and overall height. Not “about a metre” — the actual numbers, because a 50 mm difference decides whether four units fit across a container.
  2. Load per unit, and load per tier. These are different numbers. A unit holding 800 kg that is stacked four high puts 3,200 kg into the bottom frame.
  3. How many tiers, and stacked on what. On the floor, on another unit, or on a rack beam — three different structures.
  4. What handles it. Forklift, pallet jack, overhead crane, or all three. The base height follows from this, not from a standard.
  5. What goes inside. Loose parts, a palletised load, coils, sheets, or something that shifts in transit. A load that can move inside the container loads the frame in ways the drawing has to anticipate.

Send those five numbers with a photograph and the first drawing is usually the last one. Send a photograph alone and the conversation starts with the shape and never reaches the load.

Where the load path actually goes

Every stillage is a short chain of load paths: the deck takes the load, the frame spreads it, the feet pass it to whatever is underneath. Three points on that chain fail first, and all three sit where the path turns a corner.

  • The deck-to-frame joint, when the load arrives concentrated instead of spread across the deck.
  • The frame-to-foot weld collar, which is exactly where replacement feet crack.
  • The bottom frame, in any stack of more than two tiers — the bottom unit carries everything above it, and the top unit carries nothing.

Ask where the load path ends before you ask about steel thickness. Thickness cannot rescue a path that turns badly.

What we will not do

We are a steel fabricator. We cut tube and sheet, weld with robots, and run our own powder coating line with pre-treatment, a 280 °C bake and roughly two hours from one end to the other for a single piece. Electroplating and hot-dip galvanising are the only two processes we send out, and we say so rather than implying the whole plant is ours.

What we cannot do is issue a compliance certificate. If your site needs a certified personnel lifting device, a design registration, or a load test certificate from a recognised body, we are the wrong supplier — and the fact that we can weld the frame does not change that. A fabrication drawing is not a design certificate, whoever signs it.

We also hold no stock. Every unit is built to a drawing or to a sample. That is slower than picking something off a shelf, and it is the reason the drawing survives contact with the order.

The short version

A stillage earns its steel when the load has to move. If it does not move, you are buying transport you will never use, and that is the most expensive kind of steel.

If you are weighing a stillage against racking, a cage or a plate bin, send us the four answers above and a sketch. We will tell you which one we would build — including when the answer is none of ours.

Foshan Yougu Storage Equipment Co., Ltd. — custom steel storage equipment, 500–6000 mm, 300–3000 kg. Contact us for a drawing and quotation, or email ivy@fsyougu.com.

FAQ

When should I use a stillage instead of racking?

When the load has to leave the site and come back. A stillage is a transport device that also stores; racking only stores. If the unit never leaves the yard, racking usually does the job with less steel.

What is the difference between a stillage and a pallet cage?

A stillage carries its load on a deck with feet you can fork under. A pallet cage is a cage body on a pallet base. Both stack and both fork, but the stillage is normally the heavier, transport-grade option.

Should I choose mesh or solid-sided containers?

Mesh for visibility and washdown, plate for small parts, security and side impact. No single container does both well, which is why mixed fleets are common.

Can a stillage designed for two tiers be used at four?

No. Stacking loads the corner post rather than the deck, and the failure is slow enough to be missed. Specify the tier count before the structure is drawn.

Can you provide a compliance certificate for a lifting device?

No. We are a steel fabricator, not a certification body. Personnel lifting equipment needs a design certificate from a recognised body, and a fabrication drawing does not replace it.





Post time: 2026-11-19
INQUIRY NOW

Technical guides

Reference notes for buyers specifying steel storage equipment — sizes, load ratings, coating choice and container loading.